10PCS/5Pairs CCTV UTP CAT5 RJ45 AHD Balun Video Audio Power for camera passive video balun transceiver


2011HD high quality UTP video balun transmitter

No power required
AHD/HDCVI/HDTVI video format compatible
Real time transmission
Exceptional interference rejection
Wave Filter Design,Anti-Static Design,Lightning Protection
Long-distance transmission and high-quality image
Compact size and easy installation

Transmission Distance
HDCVI 720P:600m
AHD 960H/1080P:300m
HDTVI 720P/1080P:200m
Compatible Format AHD/CVI/TVI
Resolution 720P/960H/1080P
Operating Frequency DC to 6MHz
Common-mode/Different-mode rejection 15KHz to 5MHz 60 dB typ
Attenuation 1.5dB typ Max
Impedance Male BNC:75Ω
Wire type
Network Wiring One Unshield Twisted Pair(for each video signal)24-16AWG(0.5-1.31mm)
Category Type 5 or better
Impedance 100±20ohms
DC Loop Resistance 52 ohms per 1000ft(18 ohms per 100m)
DC Loop Resistance Different Capacitance
External power required No
Surge Protection Renewable solid state surge protection
Video Input 2KV(common mode),10/700us IEC6100-4-5/1995(GB/T 1726,5-1999)
Video Output 2KV(common mode),10/700us IEC6100-4-5/1995(GB/T 1726,5-1999)
Video input/output Male BNC / Push terminal
Housing ABS engineering plastic
Body Color Black
Dimensions 203*49*105mm(connector included)
Gross weight 72g/pair
Operating Temperature -20-70
Relative Humidity 0-95%(non-condensing)
Storage Temperature -40-80



CCTV video baluns, also known as UTP baluns, allow traditional coax cable to be replaced by category 5 and other forms of twisted pair wire in CCTV video camera & surveillance installations. Video baluns allow installers to use more cost effective structured cabling techniques to wire security cameras. By using video baluns, UTP wire such as cat-5 can be run over longer distances easier than coax cable and for less money. Active balun transceivers enable UTP wires for cameras to be run distances up to 5,000 feet. If you are new to the idea of using baluns for video, check out our video balun installation videos. We believes that we supply the best UTP video baluns on the market.


1.Total Absence of Signal
This problem is almost always due a discontinuity in the connection between the camera and the mux. Check the continuity of the twisted pair link.

2.Presence of Signal But No Image
This problem is most likely due to a reversal of the polarity of the wires between the two CCTV Baluns at either end. The pin designated as “Ring” must be connected to the pin designated as “Ring” at the other end.

Smearing occurs when the edge of an image leaves trail traces similar to smudging a line of ink on a piece of paper. This may occur as the length of twisted pair cable increases.Possible solutions are; a)to shorten the length of cable or b) adjust thecontrast and brightness of the monitor.

4. Flutter

Flutter occurs when the background fluctuates between light and dark. A solution to minimize this effect is to adjust the monitor’s contrast and brightness.

5. Ghosting

Ghosting is characterized by a second video image being received after the main image,resulting in a double image that is skewed in relation to the first.In these cases itis best to replace the existing cable with a new one.

6. Loss of Color and Image Detail

Loss of color or image detail may occur if twisted pair cable length exceeds the distance specifications.

Other than using an active device, one can improve the image by shortening the length of twisted pair or by eliminating other contributing signal losses such as splices, cross-connects, low-grade patch cables, etc.

Goods performance

The function of the CCTV Video Balun is to allow the traditional 75-ohm coaxial video cable to be replaced by Category 5E/6 (or better) twisted pair in the CCTV security and surveillance environment, thereby allowing CCTV camera and monitoring equipment to be deployed more cost-effectively using structured cabling techniques.

Trade show


1.Q: Are you a Video Balun factory or Video Balun trading company?

A: We are Video Balun manufacturer.

2.Q: Where is your Video Balun factory located? How can I visit there?

A: Our Video Balun factory is located in Shenzhen City, China. You can fly to Shenzhen Baoan airport directly, and we will pick you up. Welcome to visit our Video Balun factory.

3.Q: How can I get some Video Balun samples?

A: We are honored to offer you Video Balun samples, pls contact our staff and leave detailed contact information, we promise to keep your information confidential.

4.Q: How does your Video Balun factory do regarding quality control?

A: Quality is the priority. We always attach great importance to quality controlling from the start to the end. All our Video Balun products have gained CE, FCC, ROHS certification.

5.Q:What can you do?

A:1.All of our Video Balun products have proceeded aging test before shipment and we guarantee safety while using our Video Balun products.

2.Support imprint your logo on Video Balun products and let your logo shine anywhere. 3.OEM/ODM orders are warmly welcomed!

6.Q:Warranty and return:

A:1.All Video Balun products and accessories have been tested by 3 times before ship out.

2.We own the best after-sale service team, if any problem happens, our team will do our best to solve it for you.

Leave a Reply

Your email address will not be published.